'----------------------------------------------------------------
'SHOPBOT ROUTER FILE IN INCHES
'GENERATED BY PARTWorks
'Minimum extent in X = 0.000 Minimum extent in Y = 0.000 Minimum extent in Z = -0.709
'Maximum extent in X = 96.063 Maximum extent in Y = 48.031 Maximum extent in Z = 0.000
'Length of material in X = 96.063
'Length of material in Y = 48.031
'Depth of material in Z = 0.709
'Home Position Information = Bottom Left Corner, Material Surface 
'Home X = 0.000000 Home Y = 0.000000 Home Z = 0.787402
'Rapid clearance gap or Safe Z = 0.236
'UNITS:Inches
'
IF %(25)=1 THEN GOTO UNIT_ERROR	'check to see software is set to standard
SA                             	'Set program to absolute coordinate mode
CN, 90
'New Path
'Toolpath Name = Profile 1
'Tool Name   = End Mill (0.25 inch)

&PWSafeZ = 0.236
&PWZorigin = Material Surface
&PWMaterial = 0.709
'&ToolName = "End Mill (0.25 inch)"
&Tool =1           'Tool number to change to
C9                   'Change tool
TR,12000               'Set spindle RPM
C6                   'Spindle on
PAUSE 2
'
MS,1.7,0.5
JZ,0.787402
J3,3.294225,3.144024,0.236220
M3,3.294225,3.144024,-0.179134
M3,3.294225,13.372001,-0.179134
CG, ,3.419225,13.497000,0.125000,0.000000,T,1
M3,24.041487,13.497000,-0.179134
CG, ,24.166487,13.372001,0.000000,-0.125000,T,1
M3,24.166487,9.131126,-0.179134
CG, ,24.041487,9.006127,-0.125000,0.000000,T,1
M3,20.175083,9.006132,-0.179134
M3,20.175083,5.597344,-0.179134
M3,24.041487,5.597344,-0.179134
CG, ,24.166487,5.472344,0.000000,-0.125000,T,1
M3,24.166487,3.144024,-0.179134
CG, ,24.041487,3.019024,-0.125000,0.000000,T,1
M3,3.419225,3.019024,-0.179134
CG, ,3.294225,3.144024,0.000000,0.125000,T,1
M3,3.294225,3.144024,-0.358268
M3,3.294225,13.372001,-0.358268
CG, ,3.419225,13.497000,0.125000,0.000000,T,1
M3,24.041487,13.497000,-0.358268
CG, ,24.166487,13.372001,0.000000,-0.125000,T,1
M3,24.166487,9.131126,-0.358268
CG, ,24.041487,9.006127,-0.125000,0.000000,T,1
M3,20.175083,9.006132,-0.358268
M3,20.175083,5.597344,-0.358268
M3,24.041487,5.597344,-0.358268
CG, ,24.166487,5.472344,0.000000,-0.125000,T,1
M3,24.166487,3.144024,-0.358268
CG, ,24.041487,3.019024,-0.125000,0.000000,T,1
M3,3.419225,3.019024,-0.358268
CG, ,3.294225,3.144024,0.000000,0.125000,T,1
M3,3.294225,3.144024,-0.537402
M3,3.294225,13.372001,-0.537402
CG, ,3.419225,13.497000,0.125000,0.000000,T,1
M3,24.041487,13.497000,-0.537402
CG, ,24.166487,13.372001,0.000000,-0.125000,T,1
M3,24.166487,9.131126,-0.537402
CG, ,24.041487,9.006127,-0.125000,0.000000,T,1
M3,20.175083,9.006132,-0.537402
M3,20.175083,5.597344,-0.537402
M3,24.041487,5.597344,-0.537402
CG, ,24.166487,5.472344,0.000000,-0.125000,T,1
M3,24.166487,3.144024,-0.537402
CG, ,24.041487,3.019024,-0.125000,0.000000,T,1
M3,3.419225,3.019024,-0.537402
CG, ,3.294225,3.144024,0.000000,0.125000,T,1
M3,3.294225,3.144024,-0.716535
M3,3.294225,13.372001,-0.716535
CG, ,3.419225,13.497000,0.125000,0.000000,T,1
M3,24.041487,13.497000,-0.716535
CG, ,24.166487,13.372001,0.000000,-0.125000,T,1
M3,24.166487,9.131126,-0.716535
CG, ,24.041487,9.006127,-0.125000,0.000000,T,1
M3,20.175083,9.006132,-0.716535
M3,20.175083,5.597344,-0.716535
M3,24.041487,5.597344,-0.716535
CG, ,24.166487,5.472344,0.000000,-0.125000,T,1
M3,24.166487,3.144024,-0.716535
CG, ,24.041487,3.019024,-0.125000,0.000000,T,1
M3,3.419225,3.019024,-0.716535
CG, ,3.294225,3.144024,0.000000,0.125000,T,1
J3,3.294225,3.144024,0.236220
JZ,0.787402
J3,0.000000,0.000000,0.787402
'
'Turning router OFF
C7
END
'
'
UNIT_ERROR:
CN, 91                            'Run file explaining unit error
END